Installing A Tub
Installing A Tub
Blog Article
They are making a number of great annotation regarding How to Install a Bathtub Yourself overall in this content down the page.
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Installing a bathtub isn't exactly rocket science, however it does call for solid plumbing, woodworking, and also in some cases, tiling skills. Changing an old bath tub with a new one is likewise a reasonably difficult job. If the old bathtub is readily available, the job can relocate quickly; if you have to open up a wall surface to remove the old tub as well as place the brand-new bathtub, the task is much harder. In either case, the job is within a residence handyman's skills, although you will require a helper to leave the old bathtub and also set in the brand-new one. See to it you have qualified on your own for the work and are comfortable trying it. Rather than hiring a specialist to take control of a halfway-completed project, it is much better to take into consideration using one prior to you begin. Chances are you may need a professional plumber to make tube connections.
This short article will certainly assist you mount a brand-new bath tub in your bathroom if you have already bought a new tub as well as don't need to alter the plan of your previous water system pipes.
Your tools as well as material checklist ought to make up the following:
Preparing for the Installation
Firstly, the supporting structure provided with the bathroom needs to be fitted (if called for) according to the supplier's directions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to see to it that if the faucet comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps device to stop pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets making use of 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet with the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you use every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom must now be ready to be suited its last setting.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your setup, after that the first thing you must do is disconnect the water. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The process of getting rid of the existing faucets can be quite troublesome as a result of the restricted access that is commonly the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly come from the pipes. When the supply pipes have been removed, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any kind of old sealing substance.
Prior to proceeding to fit the brand-new taps, compare the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is required for the brand-new taps to fit.
Mounting the Bathtub
Making use of the two wood boards under its feet, place the tub in the called for setting. The wood boards are useful in equally spreading the weight of the bath tub over the area of the boards rather than focusing all the weight onto four tiny points.
The following goal is to guarantee that the bath tub is leveled all round. This can be achieved by examining the spirit level and changing the feet on the bath tub till the spirit level checks out degree.
To mount taps, fit the bottom of the furthest adaptable faucet connector to the suitable supply pipe by making a compression join; then do the very same for the other tap.
Turn on the water and inspect all joints and also new pipework for leaks and also tighten them if necessary. Fill up the tub as well as also inspect the overflow electrical outlet and also the normal outlet for leakages.
Ultimately, fix the bath paneling as explained in the maker's user's manual. Tiling and sealing around the tub must wait till the bathtub has been utilized a minimum of when as this will certainly settle it into its final setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the tap and the other end offers a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin guaranteeing that the washers are in place in between the faucet and also the sink. Safeguard the faucet in place with the producer offered backnut. As soon as the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The previous kind must be linked to the tap ends first, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bath meets the tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the installation can move enough to crack an inflexible seal, creating the water to pass through the wall surface between the bath and the tiling, bring about difficulties with moisture and possible leakages to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your components as well as fittings. They are sold in tubes and also cartridges, as well as are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to sealing, to allow for the activity experienced when the bathtub is in usage. The sealer can break fairly very early if you do not take into consideration this movement prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally quickly available on the marketplace. It is a good idea to fit the tiles making use of water-resistant or water-proof sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was shown that report on How to Install a Bathtub through someone on our other web address. Loved our blog? Please share it. Help another person check it out. I thank you for reading our article about A Step-by-Step Guide to Installing a Bathtub.
Visit Homepage
Report this page